Syringe Injector

Syringe Injector

  • Payment
    L/C(sight) , T/T
  • MOQ
    1 Thousand Unit(s)
  • Supply Ability
    100 Thousand Unit(s) per One-Time
  • Supply Details
    Customization
  • Country of sale
    Asia, Americas, Europe, World Wide, Middle East
  • Response Level
      41% ~ 50%
  • Supplier Level
      Less than 100 million (KRW)
  • Transaction Level
      less than 5
  • PRICE
    • EXW

      Depend on quantity

ITEM SPECIFICS

  • Brand
    Syringe Injector
  • origin
    Republic of Korea
  • Size(Capacity)
    100mm
 Syringe Injector
It s used for low pressure injection. The syringe injector is able to inject epoxy into small crack at large area at the same time, and its transparent syringe body allows you to observe the injected dosage.
 
 
◎ Features
- Very simple to operate
- Easy to carry in narrow and small space because its light weight & compact design
- Easy to exchange piston
- Low maintenance cost and Easy to clean after use
 
 
◎ Specifications
Filling Capacity 50 ml/cc
Max. Pressure 3.0 kgf / cm2
Max. Length 225mm
Min. Length 147mm
Weight 40g
 
 
 
Injecting Method(Syringe)

1. Check the cracks’ positions, widths and depths using crack gauge.
 
 
 

2. Clean the surface and remove any dust or contaminated materials from the concrete surface using scraper and wire brush, and determine the injection method.
 
 

3. Mark the places which will install pedestals. The required number of syringe per one meter depends on the conditions of concrete thickness, width, depth. In most cases, 5~6 syringes per meter is appropriate.
 
 

4. Seal the cracks using epoxy putty (DEP-009) except the marked places.
 
 

5. After applying epoxy putty at the edge of pedestal, attach the pedestals to the marked places, and make sure all cracks covered seamlessly.
 
 

6. DEL-090 is the Double component type epoxy for dry, therefore mix the resin and hardener each other with the accurate ratio of 2:1. The pot life varies depending on the site environment and the material temperature, therefore, check the pot life by mixing the small quantity before mass use.
 
 

7. Suck the mixed epoxy inside syringe (30cc), and mount the syringe into pedestal, and fasten the syringe and pedestal each other using the rubber band. (Start from low area, then go to upper area. Down → Up)
 
 

8. When epoxy is hardened, remove syringes and pedestals, and do the surface finishing work by using the hand grinder.
 

PAYMENTS DETAILS

This supplier supports payments for offline orders
  • Letter of Credit : L/C(sight)
  • Telegraphic Transfer : T/T
Notice
  • Request details on inquiry
Contact Payment manager
  • Name : Kwangsoo Choi
  • Tel : 82-2-525-6430
  • Email : conrepair@naver.com

SHIPPING

Shipping from : Republic of Korea
  • 341 Gongdan 1-daero, Siheung-si, Gyeonggi-do (15078)
ConRepair Co.,Ltd

ConRepair Co.,Ltd

www.con-repair.com Seller_Mail
  • The person in charge

    Kwangsoo Choi
  • Telephone

    82-025256430
  • Fax

    82-025984516
  • Address

    341 Gongdan 1-daero, Siheung-si, Gyeonggi-do (15078)
Introduction
Since the establishment of 2016, Conrepair.Co has been manufacturing and providing concrete waterproof, mending and reinforcing materials to domestic market. Moreover, exporting along with foreign construction with domestic construction company was the start of global embark. Currently, we are exporting to numerous countries including Canada, Australia, New Zealand, India, Singapore, Vietnam, Indonesia and Russia. Ever since company establishment we have been one of the best in the market for waterproof, reinforcing, and mending materials for concrete construction. Through continuous research and development, we are providing the best quality product to our clients. Moreover, by automatizing manufacturing facilities, cost was cut significantly. We are providing great quality products in competitive price. Also, through product diversification, we are providing various products needed for concrete waterproofing, mending and reinforcing. Conrepair.Co’s effort for providing great quality product will continue. We, ConRepair Co.,Ltd. has dedicated to waterproof & crack repair & reinforcement solution on concrete structures ever since it's foundation in 1994. As the manufacturer, exporter and supplier of injection equipment and water-poof chemicals, we have provided our superior products to construction sites as Dam, Mountain Tunnel, Subway Tunnel, Underwater Tunnel, Nuclear Power Plant, Tidal Power Plant, Deep Basement of Skyscraper, etc. in South Korea over 23 years, and has exported to all over the world. We automatized the packer production facility, and have invested R&D on chemicals, injection machines and packers in order to provide the high quality products with reasonable price to our clients. we have been keeping our good reputation for superior quality and fantastic service with our dedication and efforts.
  • Business Type :
    Manufacturer
  • Main Product :
    High Pressure Grouting Injection pump, Injection packer 10x60mm, Injection packer 10x100mm, Syringe Injector, Grease gun coupler,PolyUrethan foam, Carbon fiber
  • Established :
    12/01/2016
  • Total Annual Revenue :
    Less than 100 million (KRW)
  • Total Employees :
    5~10 people

CUSTOMER QUESTIONS & ANSWERS

0 / 4000

질문이 없습니다.
SUPPLIER BEST
  • Grouting Injection Pump
  • Injection Packer(10X60mm, 10X100mm)
  • Carbon Fiber

COMPARE TO SIMILAR ITEMS more

  • POLYCARBOXYLATES
  • Grouting Injection Pump
  • Injection Packer(10X60mm, 10X100mm)
  • Cream Type Concrete Protective Agent; CONSILATION® WR-824
  • SKYROOT