Production Introduction

After relentless research and development, the heating rail has been completely state-of-the-art technology and high quality, overcoming the problems-namely, lack of safety, inefficiency, short life, and unhealthy effects of conventional electric heating devices. For the last five years, this product has been recognized and exported globally.

Features

① 100% safety from water and fire

② Energy-saving technology

③ Semi-permanent life

④ Helps with health improvement

⑤ Beneficial for construction, building owner and customers

Application sites

Heating for house and commercial building, Heating for public, welfare and accommodation facilities, Wet floor heating

Key elements of Heating Rail(Excellent Quality)

1. Safety.  2. Energy-saving technology   3. Durability   4. Health benefits and heating efficiency   5. Advantage for construction design

1. Safety

  ① Safe from water and humidity (completely waterproof)

     * Although the finish is applied before completely drying it, the product is safe from humidity for use.  Safe from fire 

   ② no risk of overheating 

      * Maximum temperature control and wet concrete mortar technology are adopted

2. Energy-saving technology

   ① The product uses about 25% less initial power compared to other products (efficiency)  

      ** initial power: other products, about 700w per 3.3 m², Heating rail – about 450w per 3.3 m²

    ② Energy-saving by static characteristic

      ** about 35% of electric power is saved as the temperature rises with the initial power, which increases  resistance and reduces electric flow

※ According to external statistics, 350w per 3.3 m² of operating power is used on average-up to 50% of energy saving.

3. Durability

      ① Apart from the wire that sends electric current, connection in product adopted special double sheath  

so that, even if there is a crack in concrete, the sheath will not get peeled off or cut.

      ② Overall material is nonferrous metals and, therefore, has long life. (semi-permanent)

4. Health benefits and heating efficiency

     ① Concrete mortar design allows for convection (air) heating. 

            * normal electric heating tends to heat only the floor

        ② The heating effect is maximized by far-infrared radiation heating

        ③ This product also has the effect to get rid of sick house syndrome or odor caused by bacteria

5. Advantage for construction design

    ① Design to reduce the load on the building 

           * about 30mm of construction including mortar and finishing on the insulator 

           * 40% less support electricity; 50% less electricity fees per month 

※ Conclusion : Heating Rail has been perfected by attaining various mechanical and technological patents as well as safety and durability, as an energy – saving heating device

Specification of Heating Rail

1. Used materials

      ① Insulation

         ② Heating Rails

         ③ Mortar

         ④ Temperature controller

         ⑤ Others : 2 types of box tapes, connection sleeve, water proof tape, wire, tool set.

※ It is important to use standard materials and tools.

2. Construction sequence and procedure

        ① Clean until there is no foreign materials in the bottom surface (The construction of bubble concrete  or compressed Styrofoam thicker than 5cm are recommended)

        ② Install using our insulation materials of 5 – 10 mm thickness without gaps, install on the edge with a gap of approximately 5cm, Use tape for insulation joints. (5cm)

        ③ When arraying out heating rails on insulation, array them at intervals of 5 – 15cm (10) and for the edge array with gap of 5cm from insulation materials.

        ④ Connect heating rails in single connection or multiple-connection, heat the connection sleeve for the primary waterproof treatment, apply the water tape doubly and the use vise tools for the second waterproof.

        ⑤ Install the proper places through the electrical connection to the controller and the check the disconnected wire, and use through operating from the gear 1 to gear 10.

        ⑥ Inspect the installation gaps for each heating rail, check the cable connection, measure the disconnected wires by tester, supply the power and check the heat using hands.

        ⑦ Pour approximately 20-30mm mortar and plaster the floor to maintain the smoothness (for wide area, Anti-crack mash can be applied)

        ⑧ After 2-5 days of drying mortar, connect the electric power (basic cure) for re-drying for 2-3 days. And then, install the finishing material (complete drying at gear 10)

(The cause of internal moisture drying inside the mortar / Make sure to check when inspection is proceeded the status of insulator)

Contact us

t. +82-31-761-8987

f. +82-31-761-8964

m.p. +82-10-8115-8000

email : fyoon8000@gmail.com